The Amelia tea dress isn’t one I’ve sewn before but Jane who comes to my sewing class had made one last summer and I remember liking the shirred elastic midriff section. The brief for our makes this time was ‘festive’ (we usually don’t have a brief, it’s free-choice). Bearing this in mind Bobbins n Buttons had offered to provide me with fabric so I had a browse on their website and selected the Lady McElroy ‘beauty and the bees’ stretch velvet.
The pattern isn’t intended for jersey but it has simple shapes with a bit of gathering, which I knew would still work well, what you don’t want is a fabric that’s too thick or stiff though because the shirring won’t work properly. I planned to hack the pattern a bit so I decided to add long bishop sleeves as it’s winter, I also lengthened the skirt (more on that later) and of course I added pockets!
Because of the distinctive large print I opted to remove the centre back seam and put the zip into the side seam instead, this was to save me the hassle of trying to pattern match the print across the zip. Because I’d removed the CB seam in the bodice I took it out of the skirt too, for the same reasons. If you’ve got a tricky print to match over a seam like this consider whether you can move the zip to the side, it’s not much different to put in and the opening can be a little shorter but still give you sufficient room. Now I could have a line of bees central down the back (and front of course) and just needed to get a good horizontal match too for me to be really happy.
As I said before I wanted the skirt as long as possible but there needs to be a compromise between length versus flare because of the width of the fabric. If you want the skirt to be longer you’ll need to reduce the amount of flare at the hem because you’ll be restricted by the fabric width. The wider the fabric then the more scope you have. I measured how long I could make the skirt before it would need reducing at the hem and decided it would be an acceptable length. I could add around 10cms to the hem making sure the new side seams were at a right angle to each other so that the hem will run in a smooth line.
I traced around a few bees where they crossed the cutting line so that I could ensure the front and back matched as well as possible.
In order to cut everything as efficiently as possible from the fabric I first cut the skirts against the main fold-don’t forget to exclude the CB seam or the piece will be bigger than your back bodice (if you’re excluding the zip)
Then I refolded the fabric with the selvedges into the centre to cut the bodice pieces on the folds. This is vital to get those bees running down the centre.
From the remaining fabric I cut a pair of long sleeves. I used the pattern from another design I’ve made a few times, I measured the armhole of the dress and compared it against the sleeve I have. It was a little smaller at the crown so I added a small amount to give it sufficient width
Finally, because it’s jersey, I chose to use a neck binding instead of the facings so I cut two narrow strips which were each the same length as the CF to CB measurement of the neck plus a couple of centimetres seam allowance.
Ok, so I mostly followed the instruction with a few minor changes because of my alterations. One thing I did first of all was to stabilise the back shoulder seams and the left side seams where the zip was going to go with iron-on interfacing because I don’t want them to stretch out of shape.
I chose to leave the back darts in although I possibly could have eased them out as it’s a stretch fabric.
After joining the shoulder seams I added my neck binding. I folded the strips with RS out along the long edge-I didn’t join them to each other at this stage-then, starting at the V, I stitched just that section into place. This way you can sew just a small part, snip into the V and pivot at the corner more accurately. When I was happy with this I sewed the rest of the binding on leaving just the CB part unsewn, then I could join the two strips in the right place and finally attach it to the neckline. Finally I neatened the edge all the way around and then topstitched it down close to the seam to stop it rolling.
The next part is the shirring which really isn’t difficult so don’t panic. First wind shirring elastic onto an empty bobbin BY HAND stretching it very slightly as you go, put it into the machine in the usual way (you may wish to check the manual if you have an older machine in case there is anywhere else you need to thread the elastic through) Use your matching colour thread on the top in the usual way and lengthen the stitch slightly, it doesn’t need to be zigzag or anything though. Definitely try out a test piece first and don’t forget to secure the start of each new row so that the stitching doesn’t come undone. I don’t secure the other end at this stage though in case I find I need to pull the threads up any more later. You should be able to sew 8 rows of stitching parallel to each other to complete the strip. The fabric will naturally pucker up pretty well but when you’re done stitching hover the iron with plenty of steam over it and you’ll find it gathers up some more as a result. Finally knot the ends of the threads to secure.
Then you need to attach the gathered band onto the lower part of the bodice making sure it’s evenly divided as you go.
Attach the skirts (I’d sewn the pocket bags on to each side seam before doing this. I just use my handy cardboard template which I made ages ago, I just trace around it directly onto the fabric and cut out.)
Next the zip goes into the left side seam. I sew it here out of habit as I’m right-handed and find it easier to do up that way but put the zip in whichever side works for you. After neatening both side seams separately first I sewed up the top of the side seam by about 4cms from the armhole edge. I used an invisible zip and inserted it in the usual way, making sure the waist seams matched, and then joining the rest of the side seam once I was happy with the zip insertion. I sewed up the other side seam and I was ready to tackle the sleeves.
The sleeves are set-in so I made the elasticated cuffs on the flat first using straight strips of jersey the same length as the curved cuff edge.
With the strip open and RS together I sewed it once then I folded the strip in half and sewed it on the overlocker to create a channel.
This will turn downwards to form the cuff which I slotted wide elastic through, securing at both ends.
Finally, I sewed the underarm seams to create the sleeves which are inserted into the dress as per the instructions.
All that’s left to do is the hem which I sewed on the coverstitch machine which is on loan to me by Pfaff at the moment.
I’m really pleased with how the dress has turned out, it’s very swishy and has a slightly 1940’s vibe to it. I like the extra length on the skirt and the sleeves look fab. I was a little alarmed when I saw the large scale of the print but actually I really rather like the bees now. One thing I’m not keen on (and this is down to the manufacturer and not the supplier) is that they have printed a black background design onto a white base cloth. Because the cloth has a pile it means that anywhere there are joins there is a slight hint of the white showing through which is not ideal. The velour isn’t too tricky to work with as the pile is a bit flatter than velvet but it does still ‘creep’ a bit in places so if you’re in any doubt that pins aren’t enough to keep it all in alignment make sure you tack (baste) seams together. If you have a walking foot I would definitely advise using it.
Stretch velvet may feel like a challenge, but with the hints and tips in Susan’s post you’ve plenty of help and inspiration to get you started. Bobbins and Buttons also have a fantastic range of party worthy stretch velvets, with smooth or crushed velvet finishes – see below. For sizing and fabric requirements for the Amelia Tea dress find the back envelope pattern details below.
I’m loving those sleeves!